Home › Forums › snickerdoodle Baseboards › • piSmasher › USB2214b Hub Intermittent problems

Tagged: 

Viewing 1 reply thread
  • Author
    Posts
    • aerodac52
      Participant
      Post count: 1

      Hi all!

      I’m working on a project porting petalinux 2018.3 to the snickerdoodle black + pismasher configuration. I have had decent success getting most things to work, but I’ve noticed that the USB Hub has trouble enumerating and working on some boots of the petalinux flavor I’m using.

      Just a note, I am running a Pre-emptive Real-Time patched 4.14 Kernel and this issue of the USB Hub is present in builds with and without it, I honestly thought maybe the RT patch would even help the issue.

      I currently have Dual Ethernet, WiFi(Not in this build, but its been tested), and GPIO working fine, but USB seems to be random. I have been researching whether it’s an i2c bus problem or a usb hub reset problem. I have tried setting the USB Reset MIO pin to MIO 16 properly in the Zynq processing system in Vivado(this actually seems like it caused the hub initialization to initialize less, is this a GPIO conflict or something? Should I let the device-tree take care of it?) I also pulled the device tree from the Ubuntu builds for the initial time trying it, and it seemed to work great for a while. It was weird though, I have a few snickerdoodle black+ pismashers in inventory and have tested my petalinux build on 2 different devices and one of them initializes the USB Hub almost every boot(like 90%), whilst the other is probably closer to like 40%. It is also using the same MicroSD card in both black devices and yes they are both snickerdoodle blacks.

      My gut tells me its the device-tree, but I’m using the same info I found from the Ubuntu and Pynq builds, so that brings me to i2c. Am I missing pinctrl or something in the device tree, I remember reading that somewhere. Also what is pinctrl for and where is it initialized? This circle just continues forever, so if anyone has some insight please let me know.

      Below is my kernel log and device tree aka system_user.dtsi

      system_user.dtsi:

      /include/ “system-conf.dtsi”
      / {

      chosen {
      bootargs = “console=ttyPS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait “;
      stdout-path = “serial0:115200n8”;
      };

      aliases{
      eth0 = &gem0;
      eth1 = &gem1;
      mmc1 = &sdhci1;
      i2c1 = &i2c1;
      };

      power_en_reg: fixed-regulator-powen {
      compatible = “regulator-fixed”;
      regulator-name = “power-en-regulator”;
      gpio = <&gpio0 20 4>;
      regulator-min-microvolt = <1800000>;
      regulator-max-microvolt = <1800000>;
      startup-delay-us = <70000>;
      regulator-always-on;
      enable-active-high;
      };

      usb_phy0: phy0 {
      compatible = “usb-nop-xceiv”;
      #phy-cells = <0>;
      view-port = <0x170>;
      drv-vbus;
      };

      };

      &i2c1 {
      compatible = “cdns,i2c-r1p10”;
      status = “okay”;
      clocks = <0x1 0x27>;
      interrupt-parent = <0x4>;
      interrupts = <0x0 0x30 0x4>;
      reg = <0xe0005000 0x1000>;
      #address-cells = <0x1>;
      #size-cells = <0x0>;
      #clock-frequency = <0x186a0>;
      clock-frequency = <100000>;
      linux,phandle = <0x23>;

      usb2514b@2c {
      compatible = “microchip,usb2514b”;
      reg = <0x2c>;
      reset-gpios = <&gpio0 16 1>;
      };

      tlv320aic3x: tlv320aic3x@1b {
      compatible = “ti,tlv320aic3x”;
      reg = <0x1b>;
      reset-gpios = <&gpio0 17 1>;
      };
      };

      &usb0 {
      compatible = “xlnx,zynq-usb-2.20a”, “chipidea,usb2”;
      status = “okay”;
      clocks = <0x00000001 0x000000ba>;
      interrupt-parent = <0x00000003>;
      interrupts = <0x00000000 0x00000008 0x00000003>;
      reg = <0xe0002000 0x000003c4>;
      phy_type = “ulpi”;
      dr_mode = “host”;
      usb-phy = <&usb_phy0>;

      };

      &gem0 {
      compatible = “cdns,zynq-gem”, “cdns,gem”;
      reg = <0xe000b000 0x1000>;
      status = “okay”;
      interrupts = <0x0 0x16 0x4>;
      clocks = <0x1 0x1e 0x1 0x1e 0x1 0xd>;
      clock-names = “pclk”, “hclk”, “tx_clk”;
      #address-cells = <0x1>;
      #size-cells = <0x0>;
      phy-mode = “rgmii-id”;
      reset-gpios = <&gpio0 19 1>;
      linux,phandle = <0x2f>;
      phandle = <0x2f>;

      ethernet-phy@0 {
      reg = <0x0>;
      device_type = “ethernet-phy”;
      linux,phandle = <0x6>;
      phandle = <0x6>;
      };

      gmiitorgmii@8 {
      compatible = “xlnx,gmii-to-rgmii-1.0”;
      reg = <0x8>;
      phy-handle = <0x6>;
      linux,phandle = <0x30>;
      phandle = <0x30>;
      };
      };

      &gem1 {
      compatible = “cdns,zynq-gem”, “cdns,gem”;
      reg = <0xe000c000 0x1000>;
      status = “okay”;
      interrupts = <0x0 0x2d 0x4>;
      clocks = <0x1 0x1f 0x1 0x1f 0x1 0xe>;
      clock-names = “pclk”, “hclk”, “tx_clk”;
      #address-cells = <0x1>;
      #size-cells = <0x0>;
      phy-mode = “rgmii-id”;
      reset-gpios = <&gpio0 17 1>;
      linux,phandle = <0x31>;
      phandle = <0x31>;

      ethernet-phy@1 {
      reg = <0x0>;
      device_type = “ethernet-phy”;
      linux,phandle = <0x7>;
      phandle = <0x7>;
      };

      gmiitorgmii@9 {
      compatible = “xlnx,gmii-to-rgmii-1.0”;
      reg = <0x9>;
      phy-handle = <0x7>;
      linux,phandle = <0x32>;
      phandle = <0x32>;
      };
      };

      Kernel on boot:

      Zynq> boot
      Device: mmc@e0100000
      Manufacturer ID: 2
      OEM: 544d
      Name: SE04G
      Tran Speed: 50000000
      Rd Block Len: 512
      SD version 3.0
      High Capacity: Yes
      Capacity: 3.6 GiB
      Bus Width: 4-bit
      Erase Group Size: 512 Bytes
      reading image.ub
      4056092 bytes read in 235 ms (16.5 MiB/s)
      Device: mmc@e0100000
      Manufacturer ID: 2
      OEM: 544d
      Name: SE04G
      Tran Speed: 50000000
      Rd Block Len: 512
      SD version 3.0
      High Capacity: Yes
      Capacity: 3.6 GiB
      Bus Width: 4-bit
      Erase Group Size: 512 Bytes
      reading system.dtb
      15899 bytes read in 14 ms (1.1 MiB/s)
      ## Loading kernel from FIT Image at 10000000 …
      Using ‘conf@system-top.dtb’ configuration
      Verifying Hash Integrity … OK
      Trying ‘kernel@1’ kernel subimage
      Description: Linux kernel
      Type: Kernel Image
      Compression: gzip compressed
      Data Start: 0x10000104
      Data Size: 4038283 Bytes = 3.9 MiB
      Architecture: ARM
      OS: Linux
      Load Address: 0x00008000
      Entry Point: 0x00008000
      Hash algo: sha1
      Hash value: 52b72f979ce1a67d3bec7682d82390f528c64be5
      Verifying Hash Integrity … sha1+ OK
      ## Flattened Device Tree blob at 23fff000
      Booting using the fdt blob at 0x23fff000
      Uncompressing Kernel Image … OK
      Loading Device Tree to 07ff9000, end 07fffe1a … OK

      Starting kernel …

      Booting Linux on physical CPU 0x0
      Linux version 4.14.0-rt1-xilinx-v2018.3 (oe-user@oe-host) (gcc version 7.3.0 (G1
      CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
      CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
      OF: fdt: Machine model: xlnx,zynq-7000
      bootconsole [earlycon0] enabled
      Memory policy: Data cache writealloc
      cma: Reserved 16 MiB at 0x3f000000
      percpu: Embedded 17 pages/cpu @ef7cb000 s36960 r8192 d24480 u69632
      Built 1 zonelists, mobility grouping on. Total pages: 260608
      Kernel command line: console=ttyPS0,115200 earlyprintk root=/dev/mmcblk0p2 rw r
      PID hash table entries: 4096 (order: 2, 16384 bytes)
      Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
      Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
      Memory: 1012292K/1048576K available (6144K kernel code, 262K rwdata, 1612K roda)
      Virtual kernel memory layout:
      vector : 0xffff0000 – 0xffff1000 ( 4 kB)
      fixmap : 0xffc00000 – 0xfff00000 (3072 kB)
      vmalloc : 0xf0800000 – 0xff800000 ( 240 MB)
      lowmem : 0xc0000000 – 0xf0000000 ( 768 MB)
      pkmap : 0xbfe00000 – 0xc0000000 ( 2 MB)
      modules : 0xbf000000 – 0xbfe00000 ( 14 MB)
      .text : 0xc0008000 – 0xc0700000 (7136 kB)
      .init : 0xc0900000 – 0xc0a00000 (1024 kB)
      .data : 0xc0a00000 – 0xc0a41a80 ( 263 kB)
      .bss : 0xc0a41a80 – 0xc0a739ec ( 200 kB)
      SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
      Preemptible hierarchical RCU implementation.
      RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
      RCU priority boosting: priority 1 delay 500 ms.
      No expedited grace period (rcu_normal_after_boot).
      Tasks RCU enabled.
      RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
      NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
      efuse mapped to f0801000
      slcr mapped to f0803000
      L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
      L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
      L2C-310 erratum 769419 enabled
      L2C-310 enabling early BRESP for Cortex-A9
      L2C-310 full line of zeros enabled for Cortex-A9
      L2C-310 ID prefetch enabled, offset 1 lines
      L2C-310 dynamic clock gating enabled, standby mode enabled
      L2C-310 cache controller enabled, 8 ways, 512 kB
      L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
      zynq_clock_init: clkc starts at f0803100
      Zynq clock init
      sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
      clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce048b54s
      Switching to timer-based delay loop, resolution 3ns
      clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537s
      timer #0 at f080b000, irq=17
      Console: colour dummy device 80×30
      Calibrating delay loop (skipped), value calculated using timer frequency.. 666.)
      pid_max: default: 32768 minimum: 301
      Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
      Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
      CPU: Testing write buffer coherency: ok
      CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
      Setting up static identity map for 0x100000 – 0x100060
      Hierarchical SRCU implementation.
      smp: Bringing up secondary CPUs …
      CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
      smp: Brought up 1 node, 2 CPUs
      SMP: Total of 2 processors activated (1333.32 BogoMIPS).
      CPU: All CPU(s) started in SVC mode.
      devtmpfs: initialized
      VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
      clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191s
      futex hash table entries: 512 (order: 3, 32768 bytes)
      pinctrl core: initialized pinctrl subsystem
      NET: Registered protocol family 16
      DMA: preallocated 256 KiB pool for atomic coherent allocations
      cpuidle: using governor menu
      irq: type mismatch, failed to map hwirq-40 for /amba/interrupt-controller@f8f01!
      hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
      hw-breakpoint: maximum watchpoint size is 4 bytes.
      zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0880000
      zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
      e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 26, base_baud = 3124968) is as
      `��k˽���[ttyPS0] enabled
      console [ttyPS0] enabled
      bootconsole [earlycon0] disabled
      bootconsole [earlycon0] disabled
      vgaarb: loaded
      SCSI subsystem initialized
      usbcore: registered new inter
      driver usbfs
      usbcore: registered new interface driver hub
      usbcore: registered new device driver usb
      usb_phy_generic phy0: phy0 supply vcc not found, using dummy regulator
      media: Linux media interface: v0.10
      Linux video capture interface: v2.00
      pps_core: LinuxPPS API ver. 1 registered
      pps_core: Software ver. 5.3.6 – Copyright 2005-2007 Rodolfo Giometti <giometti@>
      PTP clock support registered
      EDAC MC: Ver: 3.0.0
      FPGA manager framework
      fpga-region fpga-full: FPGA Region probed
      Advanced Linux Sound Architecture Driver Initialized.
      clocksource: Switched to clocksource arm_global_timer
      NET: Registered protocol family 2
      TCP established hash table entries: 8192 (order: 3, 32768 bytes)
      TCP bind hash table entries: 8192 (order: 5, 229376 bytes)
      TCP: Hash tables configured (established 8192 bind 8192)
      UDP hash table entries: 512 (order: 3, 32768 bytes)
      UDP-Lite hash table entries: 512 (order: 3, 32768 bytes)
      NET: Registered protocol family 1
      RPC: Registered named UNIX socket transport module.
      RPC: Registered udp transport module.
      RPC: Registered tcp transport module.
      RPC: Registered tcp NFSv4.1 backchannel transport module.
      hw perfevents: no interrupt-affinity property for /pmu@f8891000, guessing.
      hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
      workingset: timestamp_bits=30 max_order=18 bucket_order=0
      jffs2: version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
      bounce: pool size: 64 pages
      io scheduler noop registered
      io scheduler deadline registered
      io scheduler cfq registered (default)
      io scheduler mq-deadline registered
      io scheduler kyber registered
      gpio-mockup: probe of gpio-mockup failed with error -22
      dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
      dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Eve6
      brd: module loaded
      loop: module loaded
      m25p80 spi0.0: found n25q128a11, expected n25q512a
      m25p80 spi0.0: n25q128a11 (16384 Kbytes)
      4 ofpart partitions found on MTD device spi0.0
      Creating 4 MTD partitions on “spi0.0”:
      0x000000000000-0x000000500000 : “boot”
      0x000000500000-0x000000520000 : “bootenv”
      0x000000520000-0x000000fa0000 : “kernel”
      0x000000fa0000-0x000001000000 : “spare”
      libphy: Fixed MDIO Bus: probed
      CAN device driver interface
      libphy: MACB_mii_bus: probed
      macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 29 (0)
      Marvell 88E1510 e000b000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E)
      macb e000c000.ethernet: invalid hw address, using random
      libphy: MACB_mii_bus: probed
      macb e000c000.ethernet eth1: Cadence GEM rev 0x00020118 at 0xe000c000 irq 30 (5)
      Marvell 88E1510 e000c000.ethernet-ffffffff:00: attached PHY driver [Marvell 88E)
      e1000e: Intel(R) PRO/1000 Network Driver – 3.2.6-k
      e1000e: Copyright(c) 1999 – 2015 Intel Corporation.
      sky2: driver version 1.30
      ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
      ehci-pci: EHCI PCI platform driver
      usbcore: registered new interface driver cdc_acm
      cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
      usbcore: registered new interface driver usb-storage
      usbcore: registered new interface driver usbserial
      usbcore: registered new interface driver usbserial_generic
      usbserial: USB Serial support registered for generic
      usbcore: registered new interface driver usb_debug
      usbserial: USB Serial support registered for debug
      usbserial: USB Serial support registered for xhci_dbc
      usbcore: registered new interface driver ftdi_sio
      usbserial: USB Serial support registered for FTDI USB Serial Device
      usbcore: registered new interface driver usb_serial_simple
      usbserial: USB Serial support registered for carelink
      usbserial: USB Serial support registered for zio
      usbserial: USB Serial support registered for funsoft
      usbserial: USB Serial support registered for flashloader
      usbserial: USB Serial support registered for google
      usbserial: USB Serial support registered for vivopay
      usbserial: USB Serial support registered for moto_modem
      usbserial: USB Serial support registered for novatel_gps
      usbserial: USB Serial support registered for hp4x
      usbserial: USB Serial support registered for suunto
      usbserial: USB Serial support registered for siemens_mpi
      of_clk_src_onecell_get: invalid clock index 186
      chipidea-usb2 e0002000.usb: e0002000.usb supply vbus not found, using dummy regr
      ci_hdrc ci_hdrc.0: missing IRQ
      i2c /dev entries driver
      cdns-i2c e0005000.i2c: 100 kHz mmio e0005000 irq 23
      IR NEC protocol handler initialized
      IR RC5(x/sz) protocol handler initialized
      IR RC6 protocol handler initialized
      IR JVC protocol handler initialized
      IR Sony protocol handler initialized
      IR SANYO protocol handler initialized
      IR Sharp protocol handler initialized
      IR MCE Keyboard/mouse protocol handler initialized
      IR XMP protocol handler initialized
      cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at f098e000 with timeout 10s
      EDAC MC: ECC not enabled
      Xilinx Zynq CpuIdle Driver started
      sdhci: Secure Digital Host Controller Interface driver
      sdhci: Copyright(c) Pierre Ossman
      sdhci-pltfm: SDHCI platform and OF driver helper
      mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA
      mmc1: SDHCI controller on e0101000.mmc [e0101000.mmc] using ADMA
      usbcore: registered new interface driver usbhid
      sdhci-arasan e0101000.mmc: card claims to support voltages below defined range
      usbhid: USB HID core driver
      mmc1: new high speed SDIO card at address 0001
      fpga_manager fpga0: Xilinx Zynq FPGA Manager registered
      NET: Registered protocol family 10
      mmc0: new high speed SDHC card at address cb6a
      Segment Routing with IPv6
      sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
      NET: Registered protocol family 17
      can: controller area network core (rev 20170425 abi 9)
      NET: Registered protocol family 29
      can: raw protocol (rev 20170425)
      can: broadcast manager protocol (rev 20170425 t)
      can: netlink gateway (rev 20170425) max_hops=1
      Registering SWP/SWPB emulation handler
      hctosys: unable to open rtc device (rtc0)
      of_cfs_init
      of_cfs_init: OK
      ALSA device list:
      No soundcards found.
      mmcblk0: mmc0:cb6a SE04G 3.64 GiB
      mmcblk0: p1 p2
      EXT4-fs (mmcblk0p2): couldn’t mount as ext3 due to feature incompatibilities
      EXT4-fs (mmcblk0p2): recovery complete
      EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
      VFS: Mounted root (ext4 filesystem) on device 179:2.
      devtmpfs: mounted
      Freeing unused kernel memory: 1024K
      INIT: version 2.88 booting
      Starting udev
      udevd[897]: starting version 3.2.2
      udevd[898]: starting eudev-3.2.2
      FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt.
      EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
      hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
      Tue Dec 7 18:59:40 UTC 2021
      hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
      Starting internet superserver: inetd.
      INIT: Entering runlevel: 5
      Configuring network interfaces… IPv6: ADDRCONF(NETDEV_UP): eth0: link is not y
      IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
      done.
      Starting system message bus: dbus.
      Starting Xserver
      Starting Dropbear SSH server:
      dropbear.
      Starting rpcbind daemon…done.

      X.Org X Server 1.19.3
      Release Date: 2017-03-15
      X Protocol Version 11, Revision 0
      Build Operating System: Linux 3.10.0-327.el7.x86_64 x86_64
      Current Operating System: Linux petalinuxsnickerdoodlep 4.14.0-rt1-xilinx-vl
      Kernel command line: console=ttyPS0,115200 earlyprintk root=/dev/mmcblk0p2 rw r
      Build Date: 03 December 2018 09:37:05PM

      Current version of pixman: 0.34.0
      Before reporting problems, check http://wiki.x.org
      to make sure that you have the latest version.
      Markers: (–) probed, (**) from config file, (==) default setting,
      (++) from command line, (!!) notice, (II) informational,
      (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
      (==) Log file: “/var/log/Xorg.0.log”, Time: Tue Dec 7 18:59:41 2021
      (==) Using system config directory “/usr/share/X11/xorg.conf.d”
      starting DNS forwarder and DHCP server: dnsmasq… (EE)
      Fatal server error:
      (EE) no screens found(EE)
      (EE)
      Please consult the The X.Org Foundation support
      at http://wiki.x.org
      for help.
      (EE) Please also check the log file at “/var/log/Xorg.0.log” for additional inf.
      (EE)
      (EE) Server terminated with error (1). Closing log file.
      done.
      hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
      Starting syslogd/klogd: done
      Starting tcf-agent: OK

    • Ryan Cousins
      Keymaster
      Post count: 343

      Hi aerodac52,

      Were you ever able to get his USB hub issue sorted out? If not, we can take a look at it on our side and come back with some suggestions.

      -Ryan

Viewing 1 reply thread
  • You must be logged in to reply to this topic.